Amazon Services
Amazon Marketplace Web Service (Amazon MWS) Documentation

Deprecation Notice:

Amazon Marketplace Web Service (MWS) will no longer be available after March 31, 2024. All MWS developers must migrate to Selling Partner API (SP-API) to avoid service disruptions. Refer to the Migration Hub for more information.

Amazon MWS Documentation

Throttling: Limits to how often you can submit requests

To use Amazon Marketplace Web Service (Amazon MWS) successfully, you need to understand throttling. Throttling is the process of limiting the number of requests you (or your authorized developer) can submit to a given operation in a given amount of time. A request can be when you submit an inventory feed or when you make an order report request. Throttling protects the web service from being overwhelmed with requests and ensures all authorized developers have access to the web service. See our MWS: Throttling video at Seller Central University for a primer on throttling.

The Leaky Bucket Algorithm

Amazon MWS uses a variation of the leaky bucket algorithm to meter the web service and implement throttling. The algorithm is based on the analogy where a bucket has a hole in the bottom from which water leaks out at a constant rate. Water can be added to the bucket intermittently, but if too much water is added at once or if water is added at too high an average rate, the water will exceed the capacity of the bucket.

To apply this analogy to Amazon MWS, imagine that the bucket represents the maximum request quota, which is the maximum number of requests you can make at one time. The hole in the bucket represents the restore rate, which is the amount of time it takes to be able to make new requests. So, if you submit too many requests at once, then the bucket overflows and, in the case of Amazon MWS, throttling occurs. If you fill up the bucket, it takes some time before you can add more water to the bucket since the water leaks from the bucket at a steady rate. So the ability to submit more requests after you have reached the maximum request quota is governed by the restore rate, the time it takes to allow you to make new requests.

Throttling Values

The definitions of these three values that control Amazon MWS throttling are:

  • Request quota - The number of requests that you can submit at one time without throttling. The request quota decreases with each request you submit, and increases at the restore rate. Requests are calculated for each Amazon seller account and Amazon MWS developer account pair.
  • Restore rate (also called the recovery rate) - The rate at which your request quota increases over time, up to the maximum request quota.
  • Maximum request quota (also called the burst rate) - The maximum size that the request quota can reach.
  • Hourly request quota - The maximum number of requests you can submit per hour.

To apply these ideas, consider this example. Imagine that you want to use the SubmitFeed operation to submit 25 inventory update feeds. The SubmitFeed operation has a request quota of 15 and a restore rate of one new request every two minutes. If you submit all 25 feed requests at once, your requests will be throttled after 15 requests. You would then have to resubmit 10 feed requests once the request quota had been restored. Since the restore rate is one request every two minutes, it would take 20 minutes for you to be able to submit the remaining 10 feed requests. So, instead of submitting all the requests and having to resubmit the requests that were throttled, you could automate your process to submit feed requests incrementally.

For example, you could submit 10 feed requests (out of your original 25 feeds), and the request quota would still have five requests left over. You could then wait 10 minutes, and the restore rate would have increased the request quota to 10 (one request every two minutes for 10 minutes gives you five new requests). You could then submit 10 more feed requests. For the remaining five feed requests, you could wait ten more minutes and then submit them. If all things go well, you would have submitted all 25 of your inventory feeds in about 20 minutes.

You should consider automating your requests and have a fallback process where, if throttling occurs because you reached the maximum request quota or the web service experienced high traffic volumes, you could slow down the number of requests you make and resubmit requests that initially failed.

Hourly Request Quotas

Some API sections (currently Products, Reports, and Feeds) have an hourly request quota in addition to the numerical request quota. This means you have a maximum number of requests you can make to a specific operation in a one-hour period. The start and end of the one-hour period varies between different callers in order to keep overall traffic balanced. For some operations, the hourly quota will be less than the restore rate multiplied by one hour. Consult the specific operation reference page for the throttling limits.

For example, ListMatchingProducts has a request quota of 20 requests, refreshing at a rate of one request every five seconds. That works out to a maximum of 720 requests per hour if the 20 request quota is not exceeded during the hour. The ListMatchingProducts operation also has an hourly quota of 720 requests. After the 720th request, further requests will result in a QuotaExceeded error until the one-hour quota resets.

Amazon MWS provides header values in each call response that show the hourly quota for the current operation; the number of calls remaining in tha quota; and the date and time when the quota will reset. For example:

x-mws-quota-max: 3600
x-mws-quota-remaining: 10
x-mws-quota-resetsOn: Wed, 06 Mar 2013 19:07:58 GMT

You can monitor these headers to determine how many more requests you can make until the reset time.

Tips on avoiding throttling

There are several things you can do to make sure your feeds and submissions are processed successfully:

  • Know the throttling limit of the specific request you are submitting.
  • Have a "back off" plan for automatically reducing the number of requests if the service is unavailable. The plan should use the restore rate value to determine when a request should be resubmitted.

You should also distribute your requests to maximize service availability:

  • Submit requests at times other than on the hour or on the half hour. For example, submit requests at 11 minutes after the hour or at 41 minutes after the hour.
  • Take advantage of times during the day when traffic is likely to be low on Amazon MWS, such as early evening or early morning hours.